RECIPROCATING COMPRESSORS
STATIONARY ELECTRIC
Commercial-Duty Electric Stationary Air compressors for the pro-consumer or heavy home hobbyist. Designed to power smaller air tools, low volume nail guns, small grinders and cut off tools.
B51V61 COMMERCIAL-DUTY COMPRESSOR
High value compressor for light commercial applications, pro-consumer or heavy home hobbyist. These units have a high cfm per HP ratio with a maximum 50% duty cycle. Designed to power smaller air tools, low volume nail guns, small grinders and cut off tools.
12 cfm @ 125 psi
14 cfm @ 40 psi
No Start-Up Kit Required
More Info
- ASME powder coated steel tank
- Auto start/stop
- Disk & spring valves
- Low rpm pump
- Solid cast iron pump
- UL electrical controls
- 60 gallon tank
- 208-230 volt
- Stainless steel flexible discharge line
- Motor overload protection built-in
B51V62 COMMERCIAL-DUTY COMPRESSOR
High value compressor for light commercial applications, pro-consumer or heavy home hobbyist. These units have a high cfm per HP ratio with a maximum 50% duty cycle. Designed to power smaller air tools, low volume nail guns, small grinders and cut off tools.
17 cfm @ 175 psi
22 cfm @ 40 psi
No Start-Up Kit Required
More Info
- ASME powder coated steel tank
- Auto start/stop
- Disk & spring valves
- Low rpm pump
- Solid cast iron pump
- UL electrical controls
- 60 gallon tank
- 208-230 volt
B51V63 COMMERCIAL-DUTY COMPRESSOR
High value compressor for light commercial applications, pro-consumer or heavy home hobbyist. These units have a high cfm per HP ratio with a maximum 50% duty cycle. Designed to power smaller air tools, low volume nail guns, small grinders and cut off tools.
16 cfm @ 175 psi
22 cfm @ 40 psi
No Start-Up Kit Required
More Info
- ASME/CRN 200 psi MWP air receiver
- Auto start/stop
- Bearings on both end of the crank shaft
- Cast iron two-stage compressor pump
- Disk & spring valves
- Heavy duty air filter
- Motor overload protection built-in
- Needle bearings and inserts on compression rod
- Stainless steel flexible discharge line
- Swedish steel valve components
- UL/CSA electric control components
OPTIONS
- Automatic tank drain
- Belt guard cooler
- NEMA7
- TEFC
- 3-phase drive motor & controls
PORTABLE ELECTRIC
Commercial-Duty Electric Portable Typically found on the farm, ranch or construction job site. Great performance in a compact system with all the power you need to complete location work.
2 HP PORTABLE ELECTRIC COMPRESSOR
Great performance in a compact system with all the power you need to complete location work. Designed for contractors and typically found on the farm, ranch or construction job site, these high value compressors deliver a high cfm per hp ratio with a maximun 50% duty cycle.
6 cfm @ 125 psi
8 cfm @ 40 psi
Free Air cfm 9.8
No Start-Up Kit Required
MORE INFO
- Auto start/stop
- Dual control operation
- Industrial grade electric motor
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty solid cast iron pump
- Heavy-duty lifting handles
- Heavy-duty solid rubber tires
- Low-profile design
- Low rpm pump
- Swedish steel valve components
- UL electrical controls
- Vibration isolation mounts
- 1/2” regulator system
- 2-piece base tank design
- 2-piece quick air connections
3 HP PORTABLE ELECTRIC COMPRESSOR
Great performance in a compact system with all the power you need to complete location work. Designed for contractors and typically found on the farm, ranch or construction job site, these high value compressors deliver a high cfm per hp ratio with a maximun 50% duty cycle.
11 cfm @ 125 psi
12 cfm @ 40 psi
Free Air cfm 20
No Start-Up Kit Required
MORE INFO
- Auto start/stop
- Dual control operation
- Industrial grade electric motor
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty solid cast iron pump
- Heavy-duty lifting handles
- Heavy-duty solid rubber tires
- Low-profile design
- Low rpm pump
- Swedish steel valve components
- UL electrical controls
- Vibration isolation mounts
- 1/2” regulator system
- 2-piece base tank design
- 2-piece quick air connections
5 HP PORTABLE ELECTRIC COMPRESSOR
Great performance in a compact system with all the power you need to complete location work. Designed for contractors and typically found on the farm, ranch or construction job site, these high value compressors deliver a high cfm per hp ratio with a maximun 50% duty cycle.
16 cfm @ 125 psi
18 cfm @ 40 psi
20 CFM Free Air
No Start-Up Kit Required
MORE INFO
- Auto start/stop
- Dual control operation
- Industrial grade electric motor
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty solid cast iron pump
- Heavy-duty lifting handles
- Heavy-duty solid rubber tires
- Low-profile design
- Low rpm pump
- Swedish steel valve components
- UL electrical controls
- Vibration isolation mounts
- 1/2” regulator system
- 2-piece base tank design
- 2-piece quick air connections
- Disc & spring valves
INDUSTRIAL-DUTY ELECTRIC
Industrial-Duty Electric Motor Compressors are designed to be used every day in automotive maintenance facilities, production facilities, fabrication facilities any many more.
5 HP Industrial-Duty Electric Compressor
The Industrial Series reciprocating compressors are designed for heavy commercial and industrial applications. Low rpm pumps provide reliable air for your applications and are manufactured for durability and long life. All of our units feature some of the most heavy duty components found in piston compressors today.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
17 cfm @175 psi
No Start-Up Kit Required
More Info
- Access to compressor valves without compressor head removal
- All UL electrical controls
- ASME tested powder coated steel tank
- Auto start/stop
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Disk and spring valves
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty two stage solid cast iron pump
- Industrial grade electric motor
- Magnetic starter mounted and wired
- Needle bearings, and inserts on rods
- Stainless steel flex air lines
- Swedish steel valves
- TEFC drive motor (3 phase only)
- Torrington needle bearings
- 2-groove B width motor pulley
- 2-piece tank top plate design
Elite Model Features
- All basic features
- Automatic tank drain
- Low oil monitor
- Tank discharge ball valve
- Vibration pads
7.5 HP Industrial-Duty Electric Compressor
The Industrial Series reciprocating compressors are designed for heavy commercial and industrial applications. Low rpm pumps provide reliable air for your applications and are manufactured for durability and long life. All of our units feature some of the most heavy duty components found in piston compressors today.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
24 cfm @175 psi
No Start-Up Kit Required
More Info
- Access to compressor valves without compressor head removal
- All UL electrical controls
- ASME tested powder coated steel tank
- Auto start/stop
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Disk and spring valves
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty two stage solid cast iron pump
- Industrial grade electric motor
- Magnetic starter mounted and wired
- Needle bearings, and inserts on rods
- Stainless steel flex air lines
- Swedish steel valves
- TEFC drive motor (3 phase only)
- Torrington needle bearings
- 2-groove B width motor pulley
- 2-piece tank top plate design
Elite Model Features
- All basic features
- Automatic tank drain
- Belt guard after cooler
- Low oil monitor
- Tank discharge ball valve
- Vibration pads
7.5 HP HEAVY-DUTY COMPRESSOR
The Industrial Series reciprocating compressors are designed for heavy commercial and industrial applications. Low rpm pumps provide reliable air for your applications and are manufactured for durability and long life. All of our units feature some of the most heavy duty components found in piston compressors today.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
28 cfm @175 psi
No Start-Up Kit Required
Air-cooled aftercooler on all Elite units
More Info
- Access to compressor valves without compressor head removal
- All UL electrical controls
- ASME tested powder coated steel tank
- Auto start/stop
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Disk and spring valves
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty two stage solid cast iron pump
- Industrial grade electric motor
- Magnetic starter mounted and wired
- Needle bearings, and inserts on rods
- Stainless steel flex air lines
- Swedish steel valves
- TEFC drive motor (3 phase only)
- Torrington needle bearings
- 2-groove B width motor pulley
- 2-piece tank top plate design
Elite Model Features
- All basic features
- Automatic tank drain
- Belt guard after cooler
- Low oil monitor
- Tank discharge ball valve
- Vibration pads
10 HP INDUSTRIAL-DUTY ELECTRIC COMPRESSORS
The Industrial Series reciprocating compressors are designed for heavy commercial and industrial applications. Low rpm pumps provide reliable air for your applications and are manufactured for durability and long life. All of our units feature some of the most heavy duty components found in piston compressors today.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
35 cfm @175 psi (3 phase)
34 cfm @175 psi (1 phase)
No Start-Up Kit Required
Air-cooled aftercooler on all Elite units
More Info
- Access to compressor valves without compressor head removal
- All UL electrical controls
- ASME tested powder coated steel tank
- Auto start/stop
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Disk and spring valves
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty two stage solid cast iron pump
- Industrial grade electric motor
- Magnetic starter mounted and wired
- Needle bearings, and inserts on rods
- Stainless steel flex air lines
- Swedish steel valves
- TEFC drive motor (3 phase only)
- Torrington needle bearings
- 2-groove B width motor pulley
- 2-piece tank top plate design
Elite Model Features
- All basic features
- Automatic tank drain
- Belt guard after cooler
- Low oil monitor
- Tank discharge ball valve
- Vibration pads
15 HP | 45 CFM INDUSTRIAL-DUTY COMPRESSORS
The Industrial Series reciprocating compressors are designed for heavy commercial and industrial applications. Low rpm pumps provide reliable air for your applications and are manufactured for durability and long life. All of our units feature some of the most heavy duty components found in piston compressors today.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
45 cfm @175 psi
No Start-Up Kit Required
Air-cooled aftercooler on all Elite units
More Info
- Access to compressor valves without compressor head removal
- All UL electrical controls
- ASME tested powder coated steel tank
- Auto start/stop
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Disk and spring valves
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty two stage solid cast iron pump
- Industrial grade electric motor
- Magnetic starter mounted and wired
- Needle bearings, and inserts on rods
- Stainless steel flex air lines
- Swedish steel valves
- TEFC drive motor (3 phase only)
- Torrington needle bearings
- 2-groove B width motor pulley
- 2-piece tank top plate design
Elite Model Features
- All basic features
- Automatic tank drain
- Belt guard after cooler
- Low oil monitor
- Tank discharge ball valve
- Vibration pads
15 HP | 51 CFM INDUSTRIAL DUTY COMPRESSORS
The Industrial Series reciprocating compressors are designed for heavy commercial and industrial applications. Low rpm pumps provide reliable air for your applications and are manufactured for durability and long life. All of our units feature some of the most heavy duty components found in piston compressors today.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
51 cfm @175 psi
No Start-Up Kit Required
Air-cooled aftercooler on all Elite units
More Info
- Acess to compressor valves without compressor head removal
- All UL electrical controls
- ASME tested powder coated steel tank
- Auto start/stop
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Disk and spring valves
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty two stage solid cast iron pump
- Industrial grade electric motor
- Magnetic starter mounted and wired
- Needle bearings, and inserts on rods
- Stainless steel flex air lines
- Swedish steel valves
- TEFC drive motor (3 phase only)
- Torrington needle bearings
- 2-groove B width motor pulley
- 2-piece tank top plate design
Elite Model Features
- All basic features
- Automatic tank drain
- Belt guard after cooler
- Low oil monitor
- Tank discharge ball valve
- Vibration pads
20 HP INDUSTRIAL-DUTY ELECTRIC COMPRESSORS
The Industrial Series reciprocating compressors are designed for heavy commercial and industrial applications. Low rpm pumps provide reliable air for your applications and are manufactured for durability and long life. All of our units feature some of the most heavy duty components found in piston compressors today.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
78 cfm @175 psi
No Start-Up Kit Required
Air-cooled aftercooler on all Elite units
More Info
- Acess to compressor valves without compressor head removal
- All UL electrical controls
- ASME tested powder coated steel tank
- Auto start/stop
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Disk and spring valves
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty two stage solid cast iron pump
- Industrial grade electric motor
- Magnetic starter mounted and wired
- Needle bearings, and inserts on rods
- Stainless steel flex air lines
- Swedish steel valves
- TEFC drive motor (3 phase only)
- Torrington needle bearings
- 2-groove B width motor pulley
- 2-piece tank top plate design
Elite Model Features
- All basic features
- Automatic tank drain
- Belt guard after cooler
- Low oil monitor
- Tank discharge ball valve
- Vibration pads
25 HP INDUSTRIAL-DUTY ELECTRIC COMPRESSORS
The Industrial Series reciprocating compressors are designed for heavy commercial and industrial applications. Low rpm pumps provide reliable air for your applications and are manufactured for durability and long life. All of our units feature some of the most heavy duty components found in piston compressors today.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
90 cfm @175 psi
No Start-Up Kit Required
Air-cooled aftercooler on all Elite units
More Info
- Acess to compressor valves without compressor head removal
- All UL electrical controls
- ASME tested powder coated steel tank
- Auto start/stop
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Disk and spring valves
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty two stage solid cast iron pump
- Industrial grade electric motor
- Magnetic starter mounted and wired
- Needle bearings, and inserts on rods
- Stainless steel flex air lines
- Swedish steel valves
- TEFC drive motor (3 phase only)
- Torrington needle bearings
- 2-groove B width motor pulley
- 2-piece tank top plate design
Elite Model Features
- All basic features
- Automatic tank drain
- Belt guard after cooler
- Low oil monitor
- Tank discharge ball valve
- Vibration pads
30 HP INDUSTRIAL DUTY ELECTRIC COMPRESSORS
The Industrial Series reciprocating compressors are designed for heavy commercial and industrial applications. Low rpm pumps provide reliable air for your applications and are manufactured for durability and long life. All of our units feature some of the most heavy duty components found in piston compressors today.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
110 cfm @175 psi
No Start-Up Kit Required
Air-cooled aftercooler on all Elite units
More Info
- Acess to compressor valves without compressor head removal
- All UL electrical controls
- ASME tested powder coated steel tank
- Auto start/stop
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Disk and spring valves
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty two stage solid cast iron pump
- Industrial grade electric motor
- Magnetic starter mounted and wired
- Needle bearings, and inserts on rods
- Stainless steel flex air lines
- Swedish steel valves
- TEFC drive motor (3 phase only)
- Torrington needle bearings
- 2-groove B width motor pulley
- 2-piece tank top plate design
Elite Model Features
- All basic features
- Automatic tank drain
- Belt guard after cooler
- Low oil monitor
- Tank discharge ball valve
- Vibration pads
QUIET ENCLOSED
Quiet Enclosed compressors are wrapped in a sound attenuating enclosure, enclosed compressors combine the lowest dBA levels in the industry with highest levels of reliability, efficiency and productivity available.
QUIET ENCLOSED 5 HP
72 dBA
18 cfm @ 175 psi
20 cfm @ 125 psi
The Industrial Series reciprocating compressors are designed for heavy commercial and industrial applications. Low rpm pumps provide reliable air for your applications and are manufactured for durability and long life. All of our units feature some of the most heavy duty components found in piston compressors today. Wrapped in a sound attenuating enclosure, enclosed compressors combine the lowest dBA levels in the industry with highest levels of reliability, efficiency and productivity available.
More Info
- Access to compressor valves without compressor head removal
- Additional cooling fan to ensure proper package temperatures
- All UL electrical controls
- ASME tested powder coated steel tank
- Auto start/stop
- Automatic tank drain
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Disk and spring valves
- Easy operational controls
- Enclosure intake pre-filter
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty two stage solid cast iron pump
- Industrial grade electric motor
- Low oil monitor
- Magnetic starter mounted and wired
- Needle bearings, and inserts on rods
- Stainless steel flex air lines
- Swedish steel valves
- Tank discharge ball valve
- TEFC drive motor (3 phase only)
- Torrington needle bearings
- Vibration pads
- 2-groove B width motor pulley
- 2-piece tank top plate design
QUIET ENCLOSED 7.5 HP
72 dBA
24 cfm @ 175 psi
25 cfm @ 125 psi
The Industrial Series reciprocating compressors are designed for heavy commercial and industrial applications. Low rpm pumps provide reliable air for your applications and are manufactured for durability and long life. All of our units feature some of the most heavy duty components found in piston compressors today. Wrapped in a sound attenuating enclosure, enclosed compressors combine the lowest dBA levels in the industry with highest levels of reliability, efficiency and productivity available.
More Info
- Access to compressor valves without compressor head removal
- Additional cooling fan to ensure proper package temperatures
- All UL electrical controls
- ASME tested powder coated steel tank
- Auto start/stop
- Automatic tank drain
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Disk and spring valves
- Easy operational controls
- Enclosure intake pre-filter
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty two stage solid cast iron pump
- Industrial grade electric motor
- Low oil monitor
- Magnetic starter mounted and wired
- Needle bearings, and inserts on rods
- Stainless steel flex air lines
- Swedish steel valves
- Tank discharge ball valve
- TEFC drive motor (3 phase only)
- Torrington needle bearings
- Vibration pads
- 2-groove B width motor pulley
- 2-piece tank top plate design
QUIET ENCLOSED 7.5 HP HEAVY-DUTY
72 dBA
29 cfm @ 175 psi
33 cfm @ 125 psi
The Industrial Series reciprocating compressors are designed for heavy commercial and industrial applications. Low rpm pumps provide reliable air for your applications and are manufactured for durability and long life. All of our units feature some of the most heavy duty components found in piston compressors today. Wrapped in a sound attenuating enclosure, enclosed compressors combine the lowest dBA levels in the industry with highest levels of reliability, efficiency and productivity available.
More Info
- Access to compressor valves without compressor head removal
- Additional cooling fan to ensure proper package temperatures
- All UL electrical controls
- ASME tested powder coated steel tank
- Auto start/stop
- Automatic tank drain
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Disk and spring valves
- Easy operational controls
- Enclosure intake pre-filter
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty two stage solid cast iron pump
- Industrial grade electric motor
- Low oil monitor
- Magnetic starter mounted and wired
- Needle bearings, and inserts on rods
- Stainless steel flex air lines
- Swedish steel valves
- Tank discharge ball valve
- TEFC drive motor (3 phase only)
- Torrington needle bearings
- Vibration pads
- 2-groove B width motor pulley
- 2-piece tank top plate design
QUIET ENCLOSED 10 HP
72 dBA
3 Phase
33.5 cfm @ 175 psi
37 cfm @ 125 psi
1 Phase
32 cfm @ 175 psi
34 cfm @ 125 pso
The Industrial Series reciprocating compressors are designed for heavy commercial and industrial applications. Low rpm pumps provide reliable air for your applications and are manufactured for durability and long life. All of our units feature some of the most heavy duty components found in piston compressors today. Wrapped in a sound attenuating enclosure, enclosed compressors combine the lowest dBA levels in the industry with highest levels of reliability, efficiency and productivity available.
More Info
- Access to compressor valves without compressor head removal
- Additional cooling fan to ensure proper package temperatures
- All UL electrical controls
- ASME tested powder coated steel tank
- Auto start/stop
- Automatic tank drain
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Disk and spring valves
- Easy operational controls
- Enclosure intake pre-filter
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty two stage solid cast iron pump
- Industrial grade electric motor
- Low oil monitor
- Magnetic starter mounted and wired
- Needle bearings, and inserts on rods
- Stainless steel flex air lines
- Swedish steel valves
- Tank discharge ball valve
- TEFC drive motor (3 phase only)
- Torrington needle bearings
- Vibration pads
- 2-groove B width motor pulley
- 2-piece tank top plate design
QUIET ENCLOSED 15 HP
72 dBA
44 cfm @ 175 psi
48 cfm @ 125 psi
The Industrial Series reciprocating compressors are designed for heavy commercial and industrial applications. Low rpm pumps provide reliable air for your applications and are manufactured for durability and long life. All of our units feature some of the most heavy duty components found in piston compressors today. Wrapped in a sound attenuating enclosure, enclosed compressors combine the lowest dBA levels in the industry with highest levels of reliability, efficiency and productivity available.
More Info
- Access to compressor valves without compressor head removal
- Additional cooling fan to ensure proper package temperatures
- All UL electrical controls
- ASME tested powder coated steel tank
- Auto start/stop
- Automatic tank drain
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Disk and spring valves
- Easy operational controls
- Enclosure intake pre-filter
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty two stage solid cast iron pump
- Industrial grade electric motor
- Low oil monitor
- Magnetic starter mounted and wired
- Needle bearings, and inserts on rods
- Stainless steel flex air lines
- Swedish steel valves
- Tank discharge ball valve
- TEFC drive motor (3 phase only)
- Torrington needle bearings
- Vibration pads
- 2-groove B width motor pulley
- 2-piece tank top plate design
DUPLEX
Duplex compressors deliver additional air when needed, are easy to service, maintain and operate. All units feature heavy-duty cast iron low-RPM pumps manufactured for durability and long life and heavy-duty compoments.
5 HP DUPLEX
36 cfm @ 175 psi (Time Delay)
18 cfm @ 175 psi (Alternating)
Duplex compressors are the ultimate in electrical efficiency. Designed for redundancy in all situations and built to deliver twice the power in the same amount of space as a typical compressors. Our duplex compressors deliver additional air when needed, are easy to service, maintain and operate. All units feature heavy-duty cast iron low-RPM pumps manufactured for durability and long life and heavy-duty compoments.
More Info
- Access to compressor valves without compressor head removal
- All UL electrical controls
- ASME tested powder coated steel tank
- Auto start/stop
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Disk and spring valves
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty two stage solid cast iron pump
- Industrial grade electric motor
- Magnetic starter mounted and wired
- Needle bearings, and inserts on rods
- Stainless steel flex air lines
- Swedish steel valves
- TEFC drive motor (3 phase only)
- Torrington needle bearings
- 2-groove B width motor pulley
- 2-piece tank top plate design
Elite Model Features
- All basic features
- Automatic tank drain
- Low oil monitor
- Tank discharge ball valve
- Vibration pads
7.5 HP DUPLEX
48 cfm @ 175 psi (Time Delay)
24 cfm @ 175 psi (Alternating)
Duplex compressors are the ultimate in electrical efficiency. Designed for redundancy in all situations and built to deliver twice the power in the same amount of space as a typical compressors. Our duplex compressors deliver additional air when needed, are easy to service, maintain and operate. All units feature heavy-duty cast iron low-RPM pumps manufactured for durability and long life and heavy-duty compoments.
More Info
- Access to compressor valves without compressor head removal
- All UL electrical controls
- ASME tested powder coated steel tank
- Auto start/stop
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Disk and spring valves
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty two stage solid cast iron pump
- Industrial grade electric motor
- Magnetic starter mounted and wired
- Needle bearings, and inserts on rods
- Stainless steel flex air lines
- Swedish steel valves
- TEFC drive motor (3 phase only)
- Torrington needle bearings
- 2-groove B width motor pulley
- 2-piece tank top plate design
Elite Model Features
- All basic features
- Automatic tank drain
- Belt guard after cooler
- Low oil monitor
- Tank discharge ball valve
- Vibration pads
7.5 HP HEAVY-DUTY DUPLEX
56 cfm @ 175 psi (Time Delay)
28 cfm @ 175 psi (Alternating)
Duplex compressors are the ultimate in electrical efficiency. Designed for redundancy in all situations and built to deliver twice the power in the same amount of space as a typical compressors. Our duplex compressors deliver additional air when needed, are easy to service, maintain and operate. All units feature heavy-duty cast iron low-RPM pumps manufactured for durability and long life and heavy-duty compoments.
More Info
- Access to compressor valves without compressor head removal
- All UL electrical controls
- ASME tested powder coated steel tank
- Auto start/stop
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Disk and spring valves
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty two stage solid cast iron pump
- Industrial grade electric motor
- Magnetic starter mounted and wired
- Needle bearings, and inserts on rods
- Stainless steel flex air lines
- Swedish steel valves
- TEFC drive motor (3 phase only)
- Torrington needle bearings
- 2-groove B width motor pulley
- 2-piece tank top plate design
Elite Model Features
- All basic features
- Automatic tank drain
- Belt guard after cooler
- Low oil monitor
- Tank discharge ball valve
- Vibration pads
10 HP HEAVY-DUTY DUPLEX
10 HP 1 Phase
68 cfm @ 175 psi (Time Delay)
34 cfm @ 175 psi (Alternating)
10 HP 3 Phase
70 cfm @ 175 psi (Time Delay)
35 cfm @ 175 psi (Alternating)
Duplex compressors are the ultimate in electrical efficiency. Designed for redundancy in all situations and built to deliver twice the power in the same amount of space as a typical compressors. Our duplex compressors deliver additional air when needed, are easy to service, maintain and operate. All units feature heavy-duty cast iron low-RPM pumps manufactured for durability and long life and heavy-duty compoments.
Air-cooled aftercooler on all Elite units
More Info
- Access to compressor valves without compressor head removal
- All UL electrical controls
- ASME tested powder coated steel tank
- Auto start/stop
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Disk and spring valves
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty two stage solid cast iron pump
- Industrial grade electric motor
- Magnetic starter mounted and wired
- Needle bearings, and inserts on rods
- Stainless steel flex air lines
- Swedish steel valves
- TEFC drive motor (3 phase only)
- Torrington needle bearings
- 2-groove B width motor pulley
- 2-piece tank top plate design
Elite Model Features
- All basic features
- Automatic tank drain
- Belt guard after cooler
- Low oil monitor
- Tank discharge ball valve
- Vibration pads
15 HP DUPLEX
106 cfm @ 175 psi (Time Delay)
53 cfm @ 175 psi (Alternating)
Duplex compressors are the ultimate in electrical efficiency. Designed for redundancy in all situations and built to deliver twice the power in the same amount of space as a typical compressors. Our duplex compressors deliver additional air when needed, are easy to service, maintain and operate. All units feature heavy-duty cast iron low-RPM pumps manufactured for durability and long life and heavy-duty compoments.
Air-cooled aftercooler on all Elite units
More Info
- Access to compressor valves without compressor head removal
- All UL electrical controls
- ASME tested powder coated steel tank
- Auto start/stop
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Disk and spring valves
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty two stage solid cast iron pump
- Industrial grade electric motor
- Magnetic starter mounted and wired
- Needle bearings, and inserts on rods
- Stainless steel flex air lines
- Swedish steel valves
- TEFC drive motor (3 phase only)
- Torrington needle bearings
- 2-groove B width motor pulley
- 2-piece tank top plate design
Elite Model Features
- All basic features
- Automatic tank drain
- Belt guard after cooler
- Low oil monitor
- Tank discharge ball valve
- Vibration pads
20 HP DUPLEX
150 cfm @ 175 psi (Time Delay)
75 cfm @ 175 psi (Alternating)
Duplex compressors are the ultimate in electrical efficiency. Designed for redundancy in all situations and built to deliver twice the power in the same amount of space as a typical compressors. Our duplex compressors deliver additional air when needed, are easy to service, maintain and operate. All units feature heavy-duty cast iron low-RPM pumps manufactured for durability and long life and heavy-duty compoments.
Air-cooled aftercooler on all Elite units
More Info
- Access to compressor valves without compressor head removal
- All UL electrical controls
- ASME tested powder coated steel tank
- Auto start/stop
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Disk and spring valves
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty two stage solid cast iron pump
- Industrial grade electric motor
- Magnetic starter mounted and wired
- Needle bearings, and inserts on rods
- Stainless steel flex air lines
- Swedish steel valves
- TEFC drive motor (3 phase only)
- Torrington needle bearings
- 2-groove B width motor pulley
- 2-piece tank top plate design
Elite Model Features
- All basic features
- Automatic tank drain
- Belt guard after cooler
- Low oil monitor
- Tank discharge ball valve
- Vibration pads
25 HP DUPLEX
184 cfm @ 175 psi (Time Delay)
92 cfm @ 175 psi (Alternating)
Duplex compressors are the ultimate in electrical efficiency. Designed for redundancy in all situations and built to deliver twice the power in the same amount of space as a typical compressors. Our duplex compressors deliver additional air when needed, are easy to service, maintain and operate. All units feature heavy-duty cast iron low-RPM pumps manufactured for durability and long life and heavy-duty compoments.
Air-cooled aftercooler on all Elite units
More Info
- Access to compressor valves without compressor head removal
- All UL electrical controls
- ASME tested powder coated steel tank
- Auto start/stop
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Disk and spring valves
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty two stage solid cast iron pump
- Industrial grade electric motor
- Magnetic starter mounted and wired
- Needle bearings, and inserts on rods
- Stainless steel flex air lines
- Swedish steel valves
- TEFC drive motor (3 phase only)
- Torrington needle bearings
- 2-groove B width motor pulley
- 2-piece tank top plate design
Elite Model Features
- All basic features
- Automatic tank drain
- Belt guard after cooler
- Low oil monitor
- Tank discharge ball valve
- Vibration pads
30 HP DUPLEX
204 cfm @ 175 psi (Time Delay)
102 cfm @ 175 psi (Alternating)
Duplex compressors are the ultimate in electrical efficiency. Designed for redundancy in all situations and built to deliver twice the power in the same amount of space as a typical compressors. Our duplex compressors deliver additional air when needed, are easy to service, maintain and operate. All units feature heavy-duty cast iron low-RPM pumps manufactured for durability and long life and heavy-duty compoments.
Air-cooled aftercooler on all Elite units
More Info
- Access to compressor valves without compressor head removal
- All UL electrical controls
- ASME tested powder coated steel tank
- Auto start/stop
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Disk and spring valves
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty two stage solid cast iron pump
- Industrial grade electric motor
- Magnetic starter mounted and wired
- Needle bearings, and inserts on rods
- Stainless steel flex air lines
- Swedish steel valves
- TEFC drive motor (3 phase only)
- Torrington needle bearings
- 2-groove B width motor pulley
- 2-piece tank top plate design
Elite Model Features
- All basic features
- Automatic tank drain
- Belt guard after cooler
- Low oil monitor
- Tank discharge ball valve
- Vibration pads
CUBE INDUSTRIAL ELECTRIC
Cube Industrial-Duty Electric Compressors feature a modular design for greater flexibility in expansion, replacement or upgrades. Ideal for applications with space parameters or existing air storage.
5 HP RECIPROCATING CUBE
18 cfm @ 175 psi
The Cube Air System is the simplest to purchase, own, and operate compressor in the world. The Cube Air System allows you to purchase a functioning compressor without having to purchase an air receiver. If the site already has a certified functional air receiver you simply install the Cube Air System next to the existing tank and connect the air discharge line. If the there is no existing tank or the existing tank is no longer certified or functional you can add a stand-alone tank to the system.
More Info
- Cast iron reciprocating compressor pump
- Centrifugal unloader
- Disc and spring valves
- Discharge cooling manifold
- Easy open inline check valve
- Easy service belt guard
- Easy to read oil sight glass
- Easy service reciprocating pump platform
- Extended oil drain tube
- Industrial grade electric drive motor
- Inner stage cooler
- Minimal floor space foot print
- Multiplexing capability
- Rigid steel frame construction
- Self tensioning electric motor base
Elite Model Features
- All basic compressor features
- Belt guard mounted air after cooler
- Low oil monitor
- High-temp stainless steel flex discharge line
- Vibration isolation mounting pads
Package Options
- Class 1 Div 2 drive motor
- Coalescing filtration
- Desiccant air dryer
- Electronic automatic tank drain kit (shipped loose for installation on site) Kit includes: drain, ¼ pipe street 90 elbow, ¼ pipe 6 inch nipple
- Enrollment in factory extended service program
- Enrollment in factory extended warranty plan
- Multiplex control panel
- NEMA 4X electrical components
- NEMA 7 electrical components
- Particulate filtration
- Quick Install Kit Includes: 8ft electrical cord with plug, 6ft compressor to tank air line JIC fittings, 6ft tank to facility air line JIC fittings
- Reciprocating Pump Enclosure for noise reduction
- Refrigerated air dryer
- 30, 60, 80, 120, gallon storage tank (200 psi MWP, ASME, CRN)
7.5 HP | 24 CFM RECIPROCATING CUBE
24 cfm @ 175 psi
The Cube Air System is the simplest to purchase, own, and operate compressor in the world. The Cube Air System allows you to purchase a functioning compressor without having to purchase an air receiver. If the site already has a certified functional air receiver you simply install the Cube Air System next to the existing tank and connect the air discharge line. If the there is no existing tank or the existing tank is no longer certified or functional you can add a stand-alone tank to the system.
More Info
- Cast iron reciprocating compressor pump
- Centrifugal unloader
- Disc and spring valves
- Discharge cooling manifold
- Easy open inline check valve
- Easy service belt guard
- Easy to read oil sight glass
- Easy service reciprocating pump platform
- Extended oil drain tube
- Industrial grade electric drive motor
- Inner stage cooler
- Minimal floor space foot print
- Multiplexing capability
- Rigid steel frame construction
- Self tensioning electric motor base
Elite Model Features
- All basic compressor features
- Belt guard mounted air after cooler
- Low oil monitor
- High-temp stainless steel flex discharge line
- Vibration isolation mounting pads
Package Options
- Class 1 Div 2 drive motor
- Coalescing filtration
- Desiccant air dryer
- Electronic automatic tank drain kit (shipped loose for installation on site) Kit includes: drain, ¼ pipe street 90 elbow, ¼ pipe 6 inch nipple
- Enrollment in factory extended service program
- Enrollment in factory extended warranty plan
- Multiplex control panel
- NEMA 4X electrical components
- NEMA 7 electrical components
- Particulate filtration
- Quick Install Kit Includes: 8ft electrical cord with plug, 6ft compressor to tank air line JIC fittings, 6ft tank to facility air line JIC fittings
- Reciprocating Pump Enclosure for noise reduction
- Refrigerated air dryer
- 30, 60, 80, 120, gallon storage tank (200 psi MWP, ASME, CRN)
7.5 HP HEAVY DUTY RECIPROCATING CUBE
28 cfm @ 175 psi
The Cube Air System is the simplest to purchase, own, and operate compressor in the world. The Cube Air System allows you to purchase a functioning compressor without having to purchase an air receiver. If the site already has a certified functional air receiver you simply install the Cube Air System next to the existing tank and connect the air discharge line. If the there is no existing tank or the existing tank is no longer certified or functional you can add a stand-alone tank to the system.
More Info
- Cast iron reciprocating compressor pump
- Centrifugal unloader
- Disc and spring valves
- Discharge cooling manifold
- Easy open inline check valve
- Easy service belt guard
- Easy to read oil sight glass
- Easy service reciprocating pump platform
- Extended oil drain tube
- Industrial grade electric drive motor
- Inner stage cooler
- Minimal floor space foot print
- Multiplexing capability
- Rigid steel frame construction
- Self tensioning electric motor base
Elite Model Features
- All basic compressor features
- Belt guard mounted air after cooler
- Low oil monitor
- High-temp stainless steel flex discharge line
- Vibration isolation mounting pads
Package Options
- Class 1 Div 2 drive motor
- Coalescing filtration
- Desiccant air dryer
- Electronic automatic tank drain kit (shipped loose for installation on site) Kit includes: drain, ¼ pipe street 90 elbow, ¼ pipe 6 inch nipple
- Enrollment in factory extended service program
- Enrollment in factory extended warranty plan
- Multiplex control panel
- NEMA 4X electrical components
- NEMA 7 electrical components
- Particulate filtration
- Quick Install Kit Includes: 8ft electrical cord with plug, 6ft compressor to tank air line JIC fittings, 6ft tank to facility air line JIC fittings
- Reciprocating Pump Enclosure for noise reduction
- Refrigerated air dryer
- 30, 60, 80, 120, gallon storage tank (200 psi MWP, ASME, CRN)
10 HP RECIPROCATING CUBE
35 cfm @ 175 psi
The Cube Air System is the simplest to purchase, own, and operate compressor in the world. The Cube Air System allows you to purchase a functioning compressor without having to purchase an air receiver. If the site already has a certified functional air receiver you simply install the Cube Air System next to the existing tank and connect the air discharge line. If the there is no existing tank or the existing tank is no longer certified or functional you can add a stand-alone tank to the system.
More Info
- Cast iron reciprocating compressor pump
- Centrifugal unloader
- Disc and spring valves
- Discharge cooling manifold
- Easy open inline check valve
- Easy service belt guard
- Easy to read oil sight glass
- Easy service reciprocating pump platform
- Extended oil drain tube
- Industrial grade electric drive motor
- Inner stage cooler
- Minimal floor space foot print
- Multiplexing capability
- Rigid steel frame construction
- Self tensioning electric motor base
Elite Model Features
- All basic compressor features
- Belt guard mounted air after cooler
- Low oil monitor
- High-temp stainless steel flex discharge line
- Vibration isolation mounting pads
Package Options
- Class 1 Div 2 drive motor
- Coalescing filtration
- Desiccant air dryer
- Electronic automatic tank drain kit (shipped loose for installation on site) Kit includes: drain, ¼ pipe street 90 elbow, ¼ pipe 6 inch nipple
- Enrollment in factory extended service program
- Enrollment in factory extended warranty plan
- Multiplex control panel
- NEMA 4X electrical components
- NEMA 7 electrical components
- Particulate filtration
- Quick Install Kit Includes: 8ft electrical cord with plug, 6ft compressor to tank air line JIC fittings, 6ft tank to facility air line JIC fittings
- Reciprocating Pump Enclosure for noise reduction
- Refrigerated air dryer
- 30, 60, 80, 120, gallon storage tank (200 psi MWP, ASME, CRN)
15 HP RECIPROCATING CUBE
48 cfm @ 175 psi
The Cube Air System is the simplest to purchase, own, and operate compressor in the world. The Cube Air System allows you to purchase a functioning compressor without having to purchase an air receiver. If the site already has a certified functional air receiver you simply install the Cube Air System next to the existing tank and connect the air discharge line. If the there is no existing tank or the existing tank is no longer certified or functional you can add a stand-alone tank to the system.
More Info
- Cast iron reciprocating compressor pump
- Centrifugal unloader
- Disc and spring valves
- Discharge cooling manifold
- Easy open inline check valve
- Easy service belt guard
- Easy to read oil sight glass
- Easy service reciprocating pump platform
- Extended oil drain tube
- Industrial grade electric drive motor
- Inner stage cooler
- Minimal floor space foot print
- Multiplexing capability
- Rigid steel frame construction
- Self tensioning electric motor base
Elite Model Features
- All basic compressor features
- Belt guard mounted air after cooler
- Low oil monitor
- High-temp stainless steel flex discharge line
- Vibration isolation mounting pads
Package Options
- Class 1 Div 2 drive motor
- Coalescing filtration
- Desiccant air dryer
- Electronic automatic tank drain kit (shipped loose for installation on site) Kit includes: drain, ¼ pipe street 90 elbow, ¼ pipe 6 inch nipple
- Enrollment in factory extended service program
- Enrollment in factory extended warranty plan
- Multiplex control panel
- NEMA 4X electrical components
- NEMA 7 electrical components
- Particulate filtration
- Quick Install Kit Includes: 8ft electrical cord with plug, 6ft compressor to tank air line JIC fittings, 6ft tank to facility air line JIC fittings
- Reciprocating Pump Enclosure for noise reduction
- Refrigerated air dryer
- 30, 60, 80, 120, gallon storage tank (200 psi MWP, ASME, CRN)
COMMERCIAL DUTY GASOLINE ENGINE
High value compressors for light commercial applications, contractors, and pro-consumers. These units are designed for job site applications that require high CFM at no more than a 50% duty cycle.
5.5 HP PORTABLE HONDA GASOLINE COMPRESSORS
12 cfm @ 125 psi
14 cfm @ 40 psi
Free Air cfm 16
Great performance in a compact system with all the power you need to complete location work. Designed for contractors and typically found on the farm, ranch or construction job site, these high value compressors deliver a high cfm per hp ratio with a maximun 50% duty cycle.
More Info
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty solid cast iron pump
- Heavy-duty lifting handles
- Heavy-duty solid rubber tires
- Industrial grade gas engine
- Low profile design
- Low rpm pump
- Swedish steel valve components
- Vibration isolation mounts
- 1/2″ regulator system
- 2-piece base tank design
- 2-piece quick air connections
5.5 HP PORTABLE KOHLER GASOLINE COMPRESSORS
12 cfm @ 125 psi
14 cfm @ 40 psi
Free Air cfm 16
Great performance in a compact system with all the power you need to complete location work. Designed for contractors and typically found on the farm, ranch or construction job site, these high value compressors deliver a high cfm per hp ratio with a maximun 50% duty cycle.
More Info
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty solid cast iron pump
- Heavy-duty lifting handles
- Heavy-duty solid rubber tires
- Industrial grade gas engine
- Low profile design
- Low rpm pump
- Swedish steel valve components
- Vibration isolation mounts
- 1/2″ regulator system
- 2-piece base tank design
- 2-piece quick air connections
8.5 HP PORTABLE GASOLINE COMPRESSORS
16 cfm @ 125 psi
22 cfm @ 40 psi
Free Air cfm 24
Great performance in a compact system with all the power you need to complete location work. Designed for contractors and typically found on the farm, ranch or construction job site, these high value compressors deliver a high cfm per hp ratio with a maximun 50% duty cycle.
More Info
- Electric start
- Pilot valve continuous operation
- Fully enclosed belt guard
- Heavy-duty air filter
- Heavy-duty solid cast iron pump
- Heavy-duty lifting handles
- Heavy-duty solid rubber tires
- Industrial grade gas engine
- Low profile design
- Low rpm pump
- Swedish steel valve components
- Vibration isolation mounts
- 1/2″ regulator system
- 2-piece base tank design
- 2-piece quick air connections
INDUSTRIAL DUTY GAS / DIESEL ENGINE DRIVEN
Designed to run 1-inch impact wrenches along with any assortment of smaller air tools. Air compressors for when you need to get the job done.
10 HP DIESEL ENGINE COMPRESSOR
16 cfm @ 175 psi
No Start-Up Kit Required
Industrial-duty gas and diesel compressors are designed for applications that require air on the go. Built for durability and reliability with features designed to make these compressors simpler to use and easier to maintain than any other compressor in this class. The engine is standard on the drivers side of the vehicle. The unloader is at your finger tips so you can unload the compressor before starting to increase solenoid and starter life. The transfer tube is protected by the receiver for safety.
With the capacity to run 1-inch impact wrenches along with any assortment of air tools, this is the compressor you need to get the job done.
More Info
- Access to compressor valves without compressor head removal
- Alternator on drive engine
- ASME tested powder coated steel tank
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Critical controls protected by compressor base plate
- Disk and spring valves
- Drive engine on left side for safety
- Fully enclosed belt guard
- Full saddle mounting feet instead of pegged mounting feet
- Heavy-duty air filter
- Heavy-duty two-stage solid cast iron pump
- Industrial-duty engine
- Needle bearings, and inserts on rods
- Pilot valve continuous operation
- Stainless steel flex lines
- Swedish steel valves
- Torrington needle bearings
- 2-groove B width drive pulley
Elite Model Features
- Automatic tank drain
- Belt guard aftercooler
- On-board battery mounted and wired (No truck wiring needed)
- Tank discharge ball valve
- Vibration pads
13 HP | 23 CFM HONDA ENGINE DRIVEN COMPRESSOR
23 cfm @ 175 psi
Industrial-duty gas and diesel compressors are designed for applications that require air on the go. Built for durability and reliability with features designed to make these compressors simpler to use and easier to maintain than any other compressor in this class. The engine is standard on the drivers side of the vehicle. The unloader is at your finger tips so you can unload the compressor before starting to increase solenoid and starter life. The transfer tube is protected by the receiver for safety.
With the capacity to run 1-inch impact wrenches along with any assortment of air tools, this is the compressor you need to get the job done.
More Info
- Access to compressor valves without compressor head removal
- Alternator on drive engine
- ASME tested powder coated steel tank
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Critical controls protected by compressor base plate
- Disk and spring valves
- Drive engine on left side for safety
- Fully enclosed belt guard
- Full saddle mounting feet instead of pegged mounting feet
- Heavy-duty air filter
- Heavy-duty two-stage solid cast iron pump
- Industrial-duty engine
- Needle bearings, and inserts on rods
- Pilot valve continuous operation
- Stainless steel flex lines
- Swedish steel valves
- Torrington needle bearings
- 2-groove B width drive pulley
Elite Model Features
- Automatic tank drain
- Belt guard aftercooler
- On-board battery mounted and wired (No truck wiring needed)
- Tank discharge ball valve
- Vibration pads
14 HP | 24 CFM ENGINE DRIVEN COMPRESSOR
24 cfm @ 175 psi
No Start-Up Kit Required
Industrial-duty gas and diesel compressors are designed for applications that require air on the go. Built for durability and reliability with features designed to make these compressors simpler to use and easier to maintain than any other compressor in this class. The engine is standard on the drivers side of the vehicle. The unloader is at your finger tips so you can unload the compressor before starting to increase solenoid and starter life. The transfer tube is protected by the receiver for safety.
With the capacity to run 1-inch impact wrenches along with any assortment of air tools, this is the compressor you need to get the job done.
More Info
- Access to compressor valves without compressor head removal
- Alternator on drive engine
- ASME tested powder coated steel tank
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Critical controls protected by compressor base plate
- Disk and spring valves
- Drive engine on left side for safety
- Fully enclosed belt guard
- Full saddle mounting feet instead of pegged mounting feet
- Heavy-duty air filter
- Heavy-duty two-stage solid cast iron pump
- Industrial-duty engine
- Needle bearings, and inserts on rods
- Pilot valve continuous operation
- Stainless steel flex lines
- Swedish steel valves
- Torrington needle bearings
- 2-groove B width drive pulley
Elite Model Features
- Automatic tank drain
- Belt guard aftercooler
- On-board battery mounted and wired (No truck wiring needed)
- Tank discharge ball valve
- Vibration pads
13-14 HP 18.4 CFM ENGINE DRIVEN COMPRESSOR
18.4 cfm @ 175 psi
No Start-Up Kit Required
Industrial-duty gas and diesel compressors are designed for applications that require air on the go. Built for durability and reliability with features designed to make these compressors simpler to use and easier to maintain than any other compressor in this class. The engine is standard on the drivers side of the vehicle. The unloader is at your finger tips so you can unload the compressor before starting to increase solenoid and starter life. The transfer tube is protected by the receiver for safety.
With the capacity to run 1-inch impact wrenches along with any assortment of air tools, this is the compressor you need to get the job done.
More Info
- Easy use pump oil drain
- Easy view oil sight glass
- Electric start drive engine
- Engine idle control for fuel savings
- Engine has recharging system
- Fork slot width mounting feet for more stable base and more maneuverability
- Inline pump for smooth operation
- Low rpm pump for lower operating temperature
- Operating pressures available up to 190 psi
- OSHA compliant belt guard
- Oversized pump flywheel for better pump cooling
- Pilot valve for continuous operation
- Solid cast iron pump
- Stainless steel flexible 1200° F rated air line
- Swedish steel reed valves
- Vibration isolation mount included
- 2-stage compressor pump
- 2-piece tank design for more mounting options of compressor system
- 30 Gallon ASME/CRN Air Receiver
Options
- Battery mounted and wired
- Belt guard aftercooler
- Remote stsrting system (Kohler only)
17 HP DIESEL ENGINE DRIVEN COMPRESSOR
35 cfm @ 175 psi
No Start-Up Kit Required
Industrial-duty gas and diesel compressors are designed for applications that require air on the go. Built for durability and reliability with features designed to make these compressors simpler to use and easier to maintain than any other compressor in this class. The engine is standard on the drivers side of the vehicle. The unloader is at your finger tips so you can unload the compressor before starting to increase solenoid and starter life. The transfer tube is protected by the receiver for safety.
With the capacity to run 1-inch impact wrenches along with any assortment of air tools, this is the compressor you need to get the job done.
Air-cooled aftercooler on all Elite units
More Info
- Access to compressor valves without compressor head removal
- Alternator on drive engine
- ASME tested powder coated steel tank
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Critical controls protected by compressor base plate
- Disk and spring valves
- Drive engine on left side for safety
- Fully enclosed belt guard
- Full saddle mounting feet instead of pegged mounting feet
- Heavy-duty air filter
- Heavy-duty two-stage solid cast iron pump
- Industrial-duty engine
- Needle bearings, and inserts on rods
- Pilot valve continuous operation
- Stainless steel flex lines
- Swedish steel valves
- Torrington needle bearings
- 2-groove B width drive pulley
Elite Model Features
- Automatic tank drain
- Belt guard aftercooler
- On-board battery mounted and wired (No truck wiring needed)
- Tank discharge ball valve
- Vibration pads
18 HP GAS ENGINE DRIVEN COMPRESSOR
35 cfm @ 175 psi
No Start-Up Kit Required
Industrial-duty gas and diesel compressors are designed for applications that require air on the go. Built for durability and reliability with features designed to make these compressors simpler to use and easier to maintain than any other compressor in this class. The engine is standard on the drivers side of the vehicle. The unloader is at your finger tips so you can unload the compressor before starting to increase solenoid and starter life. The transfer tube is protected by the receiver for safety.
With the capacity to run 1-inch impact wrenches along with any assortment of air tools, this is the compressor you need to get the job done.
Air-cooled aftercooler on all Elite units
More Info
- Access to compressor valves without compressor head removal
- Alternator on drive engine
- ASME tested powder coated steel tank
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Critical controls protected by compressor base plate
- Disk and spring valves
- Drive engine on left side for safety
- Fully enclosed belt guard
- Full saddle mounting feet instead of pegged mounting feet
- Heavy-duty air filter
- Heavy-duty two-stage solid cast iron pump
- Industrial-duty engine
- Needle bearings, and inserts on rods
- Pilot valve continuous operation
- Stainless steel flex lines
- Swedish steel valves
- Torrington needle bearings
- 2-groove B width drive pulley
Elite Model Features
- Automatic tank drain
- Belt guard aftercooler
- On-board battery mounted and wired (No truck wiring needed)
- Tank discharge ball valve
- Vibration pads
24 HP DIESEL ENGINE DRIVEN COMPRESSOR
50 cfm @ 175 psi
No Start-Up Kit Required
Industrial-duty gas and diesel compressors are designed for applications that require air on the go. Built for durability and reliability with features designed to make these compressors simpler to use and easier to maintain than any other compressor in this class. The engine is standard on the drivers side of the vehicle. The unloader is at your finger tips so you can unload the compressor before starting to increase solenoid and starter life. The transfer tube is protected by the receiver for safety.
With the capacity to run 1-inch impact wrenches along with any assortment of air tools, this is the compressor you need to get the job done.
More Info
- Access to compressor valves without compressor head removal
- Alternator on drive engine
- ASME tested powder coated steel tank
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Critical controls protected by compressor base plate
- Disk and spring valves
- Drive engine on left side for safety
- Fully enclosed belt guard
- Full saddle mounting feet instead of pegged mounting feet
- Heavy-duty air filter
- Heavy-duty two-stage solid cast iron pump
- Industrial-duty engine
- Needle bearings, and inserts on rods
- Pilot valve continuous operation
- Stainless steel flex lines
- Swedish steel valves
- Torrington needle bearings
- 2-groove B width drive pulley
Elite Model Features
- Automatic tank drain
- Belt guard aftercooler
- On-board battery mounted and wired (No truck wiring needed)
- Tank discharge ball valve
- Vibration pads
Options
- Fuel tank
- Deep cycle battery
- Enclosure
25 HP GAS ENGINE DRIVEN COMPRESSOR
50 cfm @ 175 psi
No Start-Up Kit Required
Industrial-duty gas and diesel compressors are designed for applications that require air on the go. Built for durability and reliability with features designed to make these compressors simpler to use and easier to maintain than any other compressor in this class. The engine is standard on the drivers side of the vehicle. The unloader is at your finger tips so you can unload the compressor before starting to increase solenoid and starter life. The transfer tube is protected by the receiver for safety.
With the capacity to run 1-inch impact wrenches along with any assortment of air tools, this is the compressor you need to get the job done.
More Info
- Access to compressor valves without compressor head removal
- Alternator on drive engine
- ASME tested powder coated steel tank
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Critical controls protected by compressor base plate
- Disk and spring valves
- Drive engine on left side for safety
- Fully enclosed belt guard
- Full saddle mounting feet instead of pegged mounting feet
- Heavy-duty air filter
- Heavy-duty two-stage solid cast iron pump
- Industrial-duty engine
- Needle bearings, and inserts on rods
- Pilot valve continuous operation
- Stainless steel flex lines
- Swedish steel valves
- Torrington needle bearings
- 2-groove B width drive pulley
Elite Model Features
- Automatic tank drain
- Belt guard aftercooler
- On-board battery mounted and wired (No truck wiring needed)
- Tank discharge ball valve
- Vibration pads
Options
- Fuel tank
- Deep cycle battery
- Enclosure
30 GALLON ELECTRIC START KOHLER ENGINE
21 cfm @ 90 psi
16 cfm @ 175 psi
No Start-Up Kit Required
Industrial-duty gas and diesel compressors are designed for applications that require air on the go. Built for durability and reliability with features designed to make these compressors simpler to use and easier to maintain than any other compressor in this class. The engine is standard on the drivers side of the vehicle. The unloader is at your finger tips so you can unload the compressor before starting to increase solenoid and starter life. The transfer tube is protected by the receiver for safety.
With the capacity to run 1-inch impact wrenches along with any assortment of air tools, this is the compressor you need to get the job done.
More Info
- ASME/CRN approved compressor air tank
- Cast iron compressor pump
- ASME/CRN approved pressure control devices
- Easy mount compressor air regulator kit mounting holes
- Easy view oil sight gauge on compressor pump
- Electric start Kohler drive engine
- Fuel efficiency compressor control pilot valve
- Full saddle mounting feet on compressor tank for easy mounting
- Galvanized rust resistant pipe fittings
- Grade 8 mounting bolts
- Heavy-duty B width drive belt
- Heavy duty steel air compressor filter housing
- High quality Swedish steel reed valves
- High temperature, vibration resistant air discharge line
- Light weight compact design
- No critical controls mounted on the from of the compressor tank
- Pull start back up on Kohler drive engine
- 2-piece compressor tank/top plate design
CUBE INDUSTRIAL DUTY GAS ENGINE DRIVEN
Designed to fit into tight spaces in service vans, enclosed trucks or smaller service bodies. Compact units with the power to run multiple sizes of air tools.
24 CFM ENCLOSED ENGINE DRIVEN COMPRESSOR
24 cfm @ 125 psi
23 cfm @ 40 psi
This system is the simplest to purchase, own, and operate compressor in the world. This ystem allows you to purchase a functioning compressor without having to purchase an air receiver. If the site already has a certified functional air receiver you simply install the system next to the existing tank and connect the air discharge line. If the there is no existing tank or the existing tank is no longer certified or functional you can add a stand-alone tank to the system.
More Info
- Electric start drive engine
- Engine idle control to meet air demand
- Industrial grade drive engine
- Industrial grade reciprocating pump
- JIC quick connect air & oil lines
- Low engine oil shutdown
- Quick service compressor filters
- Vibration mounting pads
Package Options
- Battery for engine electric start
- Cold weather heating package
- Compressed air regulator control pack
- Cover color change
- Drive engine control extension
- High ambient temperature cooling package
- 6 or 12 gallon EPA, DOT rated fuel cells
- 6 or 30 gallon air storage tank
37 CFM ENCLOSED ENGINE DRIVEN COMPRESSOR
37 cfm @ 125 psi
35 cfm @ 175 psi
This system is the simplest to purchase, own, and operate compressor in the world. This ystem allows you to purchase a functioning compressor without having to purchase an air receiver. If the site already has a certified functional air receiver you simply install the system next to the existing tank and connect the air discharge line. If the there is no existing tank or the existing tank is no longer certified or functional you can add a stand-alone tank to the system.
More Info
- Electric start drive engine
- Engine idle control to meet air demand
- Industrial grade drive engine
- Industrial grade reciprocating pump
- JIC quick connect air & oil lines
- Low engine oil shutdown
- Quick service compressor filters
- Vibration mounting pads
Package Options
- Battery for engine electric start
- Cold weather heating package
- Compressed air regulator control pack
- Cover color change
- Drive engine control extension
- High ambient temperature cooling package
- 6 or 12 gallon EPA, DOT rated fuel cells
- 6 or 30 gallon air storage tank
5.5 HP ENGINE DRIVEN RECIPROCATING CUBE
12 cfm @ 125 psi
This system is the simplest to purchase, own, and operate compressor in the world. This ystem allows you to purchase a functioning compressor without having to purchase an air receiver. If the site already has a certified functional air receiver you simply install the system next to the existing tank and connect the air discharge line. If the there is no existing tank or the existing tank is no longer certified or functional you can add a stand-alone tank to the system.
More Info
- Centrifugal unloader
- Discharge cooling manifold
- Easy open inline check valve
- Easy service belt guard
- Easy to read oil sight glass
- Easy to mount installation feet
- Electric start drive engine
- Extended oil drain tube
- Inner stage cooler
- Minimal floor space foot print
- Multiplexing capability
- Rigid steel frame construction
- Self tensioning motor base
- 2 belt drive system
Elite Model Features
- All basic compressor features
- Belt guard mounted air after cooler
- Low oil monitor
- High-temp stainless steel flex discharge line
- Vibration isolation mounting pads
Package Options
- Coalescing filtration
- Desiccant air dryer
- Electronic automatic tank drain kit (shipped loose for installation on site) Kit includes: drain, ¼ pipe street 90 elbow, ¼ pipe 6 inch nipple
- Enrollment in factory extended service program
- Enrollment in factory extended warranty plan
- Particulate filtration
- Quick Install Kit Includes: 8ft electrical cord with plug, 6ft compressor to tank air line JIC fittings, 6ft tank to facility air line JIC fittings
- Reciprocating Pump Enclosure for noise reduction
- Refrigerated air dryer
- 30, 60, 80, 120, gallon storage tank (200 psi MWP, ASME, CRN)
13-14 HP ENGINE DRIVEN RECIPROCATING CUBE
23 cfm @ 175 psi
This system is the simplest to purchase, own, and operate compressor in the world. This ystem allows you to purchase a functioning compressor without having to purchase an air receiver. If the site already has a certified functional air receiver you simply install the system next to the existing tank and connect the air discharge line. If the there is no existing tank or the existing tank is no longer certified or functional you can add a stand-alone tank to the system.
More Info
- Centrifugal unloader
- Discharge cooling manifold
- Easy open inline check valve
- Easy service belt guard
- Easy to read oil sight glass
- Easy to mount installation feet
- Electric start drive engine
- Extended oil drain tube
- Inner stage cooler
- Minimal floor space foot print
- Multiplexing capability
- Rigid steel frame construction
- Self tensioning motor base
- 2 belt drive system
Elite Model Features
- All basic compressor features
- Belt guard mounted air after cooler
- Low oil monitor
- High-temp stainless steel flex discharge line
- Vibration isolation mounting pads
Package Options
- Coalescing filtration
- Desiccant air dryer
- Electronic automatic tank drain kit (shipped loose for installation on site) Kit includes: drain, ¼ pipe street 90 elbow, ¼ pipe 6 inch nipple
- Enrollment in factory extended service program
- Enrollment in factory extended warranty plan
- Particulate filtration
- Quick Install Kit Includes: 8ft electrical cord with plug, 6ft compressor to tank air line JIC fittings, 6ft tank to facility air line JIC fittings
- Reciprocating Pump Enclosure for noise reduction
- Refrigerated air dryer
- 30, 60, 80, 120, gallon storage tank (200 psi MWP, ASME, CRN)
INDUSTRIAL DUTY HYDRAULIC
Industrial-Duty Hydraulic motor driven air compressors driven by hydraulic drive motors that will run a wide assortment of impact wrenches along with any assortment of smaller air tools.
17 CFM ENCLOSED HYDRAULIC DRIVEN COMPRESSOR
17 cfm @ 100 psi
14 cfm @ 150 psi
Enclosed hydraulic-driven air compressors deliver extreme job-site power. Wrapped in a sound attenuating enclosure, enclosed compressors combine the lowest dBA levels in the industry with highest levels of reliability, efficiency and productivity available. A great fit for any mission-critical application, the 100% duty cycle assures the compressor can not be overworked. Quality components, simple controls, easy maintenance and once a year oil changes make this a great solution for high-volume and high productivity environments.
More Info
- All hydraulic fluid and air connections on same side
- ASME/CRN certified safety valves
- Bearings on both ends of crank shaft
- CAS SMART fluid control system
- Compressor load/unload operation
- Disk and spring valves
- Easy to remove compressor cover
- External NEMA 4 on/off switch
- Heavy-duty two-stage solid cast-iron pumps
- Hydraulic fluid flow regulator
- Hydraulic fluid pressure regulator
- Hydraulic fluid bypass valve
- Intake filter silencer
- Needle bearings and inserts on rods
- NEMA 4 load/unload switch
- Steel mounting plate
- Vibration mounting pads
- 12 volt compressor air & oil cooler pack*
- 12 volt control system*
Options
- Cold weather heating package
- Cover color change
- High ambient temperature cooling package
- Hose reels
- Hydraulic fluid cooler
- Tank mounted
- 24 volt operation
- 110 volt operation
*Cooler pack to be mounted external to compressor system. 12 Volt Control voltage connection to be supplied by vehicle/equipment compressor is mounted to.
Do not let hydraulic fluid exceed 190 ℉. Dimensions are representatives of package dimensions not total space required for mounting
24 CFM ENCLOSED HYDRAULIC DRIVEN COMPRESSOR
24 cfm @ 100 psi
22 cfm @ 150 psi
Enclosed hydraulic-driven air compressors deliver extreme job-site power. Wrapped in a sound attenuating enclosure, enclosed compressors combine the lowest dBA levels in the industry with highest levels of reliability, efficiency and productivity available. A great fit for any mission-critical application, the 100% duty cycle assures the compressor can not be overworked. Quality components, simple controls, easy maintenance and once a year oil changes make this a great solution for high-volume and high productivity environments.
More Info
- All hydraulic fluid and air connections on same side
- ASME/CRN certified safety valves
- Bearings on both ends of crank shaft
- CAS SMART fluid control system
- Compressor load/unload operation
- Disk and spring valves
- Easy to remove compressor cover
- External NEMA 4 on/off switch
- Heavy-duty two-stage solid cast-iron pumps
- Hydraulic fluid flow regulator
- Hydraulic fluid pressure regulator
- Hydraulic fluid bypass valve
- Intake filter silencer
- Needle bearings and inserts on rods
- NEMA 4 load/unload switch
- Steel mounting plate
- Vibration mounting pads
- 12 volt compressor air & oil cooler pack*
- 12 volt control system*
Options
- Cold weather heating package
- Cover color change
- High ambient temperature cooling package
- Hose reels
- Hydraulic fluid cooler
- Tank mounted
- 24 volt operation
- 110 volt operation
*Cooler pack to be mounted external to compressor system. 12 Volt Control voltage connection to be supplied by vehicle/equipment compressor is mounted to.
Do not let hydraulic fluid exceed 190 ℉. Dimensions are representatives of package dimensions not total space required for mounting
45 CFM ENCLOSED HYDRAULIC DRIVEN COMPRESSOR
45 cfm @ 100 psi
40 cfm @ 150 psi
Enclosed hydraulic-driven air compressors deliver extreme job-site power. Wrapped in a sound attenuating enclosure, enclosed compressors combine the lowest dBA levels in the industry with highest levels of reliability, efficiency and productivity available. A great fit for any mission-critical application, the 100% duty cycle assures the compressor can not be overworked. Quality components, simple controls, easy maintenance and once a year oil changes make this a great solution for high-volume and high productivity environments.
More Info
- All hydraulic fluid and air connections on same side
- ASME/CRN certified safety valves
- Bearings on both ends of crank shaft
- CAS SMART fluid control system
- Compressor load/unload operation
- Disk and spring valves
- Easy to remove compressor cover
- External NEMA 4 on/off switch
- Heavy-duty two-stage solid cast-iron pumps
- Hydraulic fluid flow regulator
- Hydraulic fluid pressure regulator
- Hydraulic fluid bypass valve
- Intake filter silencer
- Needle bearings and inserts on rods
- NEMA 4 load/unload switch
- Steel mounting plate
- Vibration mounting pads
- 12 volt compressor air & oil cooler pack*
- 12 volt control system*
Options
- Cold weather heating package
- Cover color change
- High ambient temperature cooling package
- Hose reels
- Hydraulic fluid cooler
- Tank mounted
- 24 volt operation
- 110 volt operation
*Cooler pack to be mounted external to compressor system. 12 Volt Control voltage connection to be supplied by vehicle/equipment compressor is mounted to.
Do not let hydraulic fluid exceed 190 ℉. Dimensions are representatives of package dimensions not total space required for mounting
COMPRESSOR COMBINATION PACKAGES INDUSTRIAL DUTY AIR
Compressor Combination Packages Industrial Duty air compressors for maintenance trucks, service fleets or technicians that need to save space and weight. With power to run 1-inch impact wrenches combined with generators, welders or jump starters in the field or on the job site, this is what you need when you need to get the job done.
16 CFM DIESEL ENGINE COMPRESSOR / GENERATOR
16 cfm @ 175 psi
5000 Watt Generator
No Start-Up Kit Required
Industrial-duty gas and diesel compressors are designed for applications that require air on the go. Built for durability and reliability with features designed to make these compressors simpler to use and easier to maintain than any other compressor in this class. The engine is standard on the drivers side of the vehicle. The unloader is at your finger tips so you can unload the compressor before starting to increase solenoid and starter life. The transfer tube is protected by the receiver for safety.
With the capacity to run 1-inch impact wrenches along with any assortment of air tools, this is the compressor you need to get the job done.
Air-cooled aftercooler on all Elite units
More Info
- Access to compressor valves without compressor head removal
- Alternator on drive engine
- ASME tested powder coated steel tank
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Critical controls protected by compressor base plate
- Disk and spring valves
- Drive engine on left side for safety
- Fully enclosed belt guard
- Full saddle mounting feet instead of pegged mounting feet
- Heavy-duty air filter
- Heavy-duty two-stage solid cast iron pump
- Industrial-duty engine
- Needle bearings, and inserts on rods
- Pilot valve continuous operation
- Stainless steel flex lines
- Swedish steel valves
- Torrington needle bearings
- 2-groove B width drive pulley
Elite Model Features
- Automatic tank drain
- Belt guard aftercooler
- On-board battery mounted and wired (No truck wiring needed)
- Tank discharge ball valve
- Vibration pads
16.5 CFM GAS ENGINE COMPRESSOR / GENERATOR
16.5 cfm @ 175 psi
Industrial Grade 3400 Watt Generator
Electric Start Engine
No Start-Up Kit Required
Industrial-duty gas and diesel compressors are designed for applications that require air on the go. Built for durability and reliability with features designed to make these compressors simpler to use and easier to maintain than any other compressor in this class. The engine is standard on the drivers side of the vehicle. The unloader is at your finger tips so you can unload the compressor before starting to increase solenoid and starter life. The transfer tube is protected by the receiver for safety.
With the capacity to run 1-inch impact wrenches along with any assortment of air tools, this is the compressor you need to get the job done.
More Info
- Access to compressor valves without compressor head removal
- Alternator on drive engine
- ASME tested powder coated steel tank
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Critical controls protected by compressor base plate
- Disk and spring valves
- Drive engine on left side for safety
- Fully enclosed belt guard
- Full saddle mounting feet instead of pegged mounting feet
- Heavy-duty air filter
- Heavy-duty two-stage solid cast iron pump
- Industrial-duty engine
- Needle bearings, and inserts on rods
- Pilot valve continuous operation
- Stainless steel flex lines
- Swedish steel valves
- Torrington needle bearings
- 2-groove B width drive pulley
Options
- Automatic tank drain
- Battery mounted and wired
- Filter Regulator
19 CFM GAS ENGINE COMPRESSOR / GENERATOR
19.5 cfm @ 175 psi
5000 Watt Generator
No Start-Up Kit Required
Industrial-duty gas and diesel compressors are designed for applications that require air on the go. Built for durability and reliability with features designed to make these compressors simpler to use and easier to maintain than any other compressor in this class. The engine is standard on the drivers side of the vehicle. The unloader is at your finger tips so you can unload the compressor before starting to increase solenoid and starter life. The transfer tube is protected by the receiver for safety.
With the capacity to run 1-inch impact wrenches along with any assortment of air tools, this is the compressor you need to get the job done.
More Info
- Access to compressor valves without compressor head removal
- Alternator on drive engine
- ASME tested powder coated steel tank
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Critical controls protected by compressor base plate
- Disk and spring valves
- Drive engine on left side for safety
- Fully enclosed belt guard
- Full saddle mounting feet instead of pegged mounting feet
- Heavy-duty air filter
- Heavy-duty two-stage solid cast iron pump
- Industrial-duty engine
- Needle bearings, and inserts on rods
- Pilot valve continuous operation
- Stainless steel flex lines
- Swedish steel valves
- Torrington needle bearings
- 2-groove B width drive pulley
Generator Features
- 110/220 volt outlets
- 41 amps @ 120 volt}
- 20 amps @ 240 volt}
Elite Model Features
- Automatic tank drain
- Belt guard aftercooler
- On-board battery mounted and wired (No truck wiring needed)
- Tank discharge ball valve
- Vibration pads
23 CFM GAS / DIESEL ENGINE COMPRESSOR / GENERATOR
23 cfm @ 175 psi
5500 Watt Generator
No Start-Up Kit Required
Industrial-duty gas and diesel compressors are designed for applications that require air on the go. Built for durability and reliability with features designed to make these compressors simpler to use and easier to maintain than any other compressor in this class. The engine is standard on the drivers side of the vehicle. The unloader is at your finger tips so you can unload the compressor before starting to increase solenoid and starter life. The transfer tube is protected by the receiver for safety.
With the capacity to run 1-inch impact wrenches along with any assortment of air tools, this is the compressor you need to get the job done.
Air-cooled aftercooler on all Elite units
More Info
- Access to compressor valves without compressor head removal
- Alternator on drive engine
- ASME tested powder coated steel tank
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Critical controls protected by compressor base plate
- Disk and spring valves
- Drive engine on left side for safety
- Fully enclosed belt guard
- Full saddle mounting feet instead of pegged mounting feet
- Heavy-duty air filter
- Heavy-duty two-stage solid cast iron pump
- Industrial-duty engine
- Needle bearings, and inserts on rods
- Pilot valve continuous operation
- Stainless steel flex lines
- Swedish steel valves
- Torrington needle bearings
- 2-groove B width drive pulley
Generator Features
- 5500 Watt Generator
- 110/220 volt outlets
- 41 amps @ 120 volt}
- 20 amps @ 240 volt}
Elite Model Features
- Automatic tank drain
- Belt guard aftercooler
- On-board battery mounted and wired (No truck wiring needed)
- Tank discharge ball valve
- Vibration pads
16 CFM DIESEL COMPRESSOR / GENERATOR / WELDER
16 cfm @ 175 psi
210 Amp Welders
5000 Watt Generator
No Start-Up Kit Required
Industrial-duty gas and diesel compressors are designed for applications that require air on the go. Built for durability and reliability with features designed to make these compressors simpler to use and easier to maintain than any other compressor in this class. The engine is standard on the drivers side of the vehicle. The unloader is at your finger tips so you can unload the compressor before starting to increase solenoid and starter life. The transfer tube is protected by the receiver for safety.
With the capacity to run 1-inch impact wrenches along with any assortment of air tools, this is the compressor you need to get the job done.
More Info
- Access to compressor valves without compressor head removal
- Alternator on drive engine
- ASME tested powder coated steel tank
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Critical controls protected by compressor base plate
- Disk and spring valves
- Drive engine on left side for safety
- Fully enclosed belt guard
- Full saddle mounting feet instead of pegged mounting feet
- Heavy-duty air filter
- Heavy-duty two-stage solid cast iron pump
- Industrial-duty engine
- Needle bearings, and inserts on rods
- Pilot valve continuous operation
- Stainless steel flex lines
- Swedish steel valves
- Torrington needle bearings
- 2-groove B width drive pulley
Generator Features
- 120/220 volt outlets
- 41 amps @ 120 volt}
- 20 amps @ 240 volt}
Options
- Engine control extension
- Filter Regulator
- Front mount battery
- Heavy-duty marine-grade battery
16 CFM GAS OR DIESEL COMPRESSOR / GENERATOR / WELDER
16 cfm @ 175 psi
210 Amp Welders
5000 Watt Generator
No Start-Up Kit Required
Industrial-duty gas and diesel compressors are designed for applications that require air on the go. Built for durability and reliability with features designed to make these compressors simpler to use and easier to maintain than any other compressor in this class. The engine is standard on the drivers side of the vehicle. The unloader is at your finger tips so you can unload the compressor before starting to increase solenoid and starter life. The transfer tube is protected by the receiver for safety.
With the capacity to run 1-inch impact wrenches along with any assortment of air tools, this is the compressor you need to get the job done.
More Info
- Access to compressor valves without compressor head removal
- Alternator on drive engine
- ASME tested powder coated steel tank
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Critical controls protected by compressor base plate
- Disk and spring valves
- Drive engine on left side for safety
- Fully enclosed belt guard
- Full saddle mounting feet instead of pegged mounting feet
- Heavy-duty air filter
- Heavy-duty two-stage solid cast iron pump
- Industrial-duty engine
- Needle bearings, and inserts on rods
- Pilot valve continuous operation
- Stainless steel flex lines
- Swedish steel valves
- Torrington needle bearings
- 2-groove B width drive pulley
Generator Features
- 5000 Watt Generator
- 110/220 volt outlets
- 41 amps @ 120 volt}
- 20 amps @ 240 volt}
Options
- Automatic tank drain
- Battery mounted and wired
- Belt guard aftercooler
- Filter Regulator
19 CFM COMPRESSOR / GENERATOR / WELDER
19 cfm @ 175 psi
5000 Watt Generator
No Start-Up Kit Required
Industrial-duty gas and diesel compressors are designed for applications that require air on the go. Built for durability and reliability with features designed to make these compressors simpler to use and easier to maintain than any other compressor in this class. The engine is standard on the drivers side of the vehicle. The unloader is at your finger tips so you can unload the compressor before starting to increase solenoid and starter life. The transfer tube is protected by the receiver for safety.
With the capacity to run 1-inch impact wrenches along with any assortment of air tools, this is the compressor you need to get the job done.
Air-cooled aftercooler on all Elite units
More Info
- Access to compressor valves without compressor head removal
- Alternator on drive engine
- ASME tested powder coated steel tank
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Critical controls protected by compressor base plate
- Disk and spring valves
- Drive engine on left side for safety
- Fully enclosed belt guard
- Full saddle mounting feet instead of pegged mounting feet
- Heavy-duty air filter
- Heavy-duty two-stage solid cast iron pump
- Industrial-duty engine
- Needle bearings, and inserts on rods
- Pilot valve continuous operation
- Stainless steel flex lines
- Swedish steel valves
- Torrington needle bearings
- 2-groove B width drive pulley
Generator / Welder Features
- 110/220 volt outlets
- 41 amps @ 120 volt}
- 20 amps @ 240 volt}
- Automatic tank drain
- Belt guard aftercooler
- On-board battery mounted and wired (No truck wiring needed)
- Tank discharge ball valve
- Vibration pads
23 CFM COMPRESSOR / GENERATOR / WELDER / JUMP STARTER
23 cfm @ 175 psi
6000 Watt Generator
300 Amp Welder
300 Amp Jump Starter
300 Amp Jump Charger
No Start-Up Kit Required
Industrial-duty gas and diesel compressors are designed for applications that require air on the go. Built for durability and reliability with features designed to make these compressors simpler to use and easier to maintain than any other compressor in this class. The engine is standard on the drivers side of the vehicle. The unloader is at your finger tips so you can unload the compressor before starting to increase solenoid and starter life. The transfer tube is protected by the receiver for safety.
With the capacity to run 1-inch impact wrenches along with any assortment of air tools, this is the compressor you need to get the job done.
More Info
- Access to compressor valves without compressor head removal
- Alternator on drive engine
- ASME tested powder coated steel tank
- Bearings on both ends of the crank shaft
- Centrifugal unloader
- Critical controls protected by compressor base plate
- Disk and spring valves
- Drive engine on left side for safety
- Fully enclosed belt guard
- Full saddle mounting feet instead of pegged mounting feet
- Heavy-duty air filter
- Heavy-duty two-stage solid cast iron pump
- Industrial-duty engine
- Needle bearings, and inserts on rods
- Pilot valve continuous operation
- Stainless steel flex lines
- Swedish steel valves
- Torrington needle bearings
- 2-groove B width drive pulley
Options
- Cold weather heating kit
- DOT approved fuel cell
- Filter regulator
- Heavy-duty marine-grade battery
- Skid mounted package with or without tank
- 37 cfm @ 175 psi
- 51 cfm @ 175 psi
- 50 ft welding cables
- 50 ft jump starting/charging cables
- 50, 80 or 120 gallon tank
OIL-FREE INDUSTRIAL DUTY
Industrial-Duty Oil-Free Air compressor for the medical, agricultural, food, beverage and laboratory environments. These units ensure your process or tools have oil-free air.
Industrial Duty Pressure Lubricated Air Compressors that have internal oil pumps to make sure they stay lubricated even in the harshest environments.
2 HP OIL-FREE INDUSTRIAL DUTY COMPRESSOR
6 cfm @ 125 psi
No Start-Up Kit Required
Oil-free compressors are designed for the medical, agricultural, food, beverage and laboratory environments. These units ensure your process or tools have oil-free air. Our low rpm pumps provide reliable air for any applications and are manufactured for durability and long life. Built with the most heavy-duty components found in piston compressors today.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
More Info
- All UL electrical controls
- ASME/CRN powder coated air receiver
- Auto start/stop
- Magnetic motor starter
- Fully enclosed belt guard
- Heavy-duty air filters
- Heavy-duty industrial-grade electric motor
- Heavy-duty single-stage oil-free industrial-grade pump
Generator / Welder Features
- All basic features
- Belt guard aftercooler
- Tank discharge ball valve
- Vibration pads
3 HP OIL-FREE INDUSTRIAL DUTY COMPRESSOR
10 cfm @ 125 psi
No Start-Up Kit Required
Oil-free compressors are designed for the medical, agricultural, food, beverage and laboratory environments. These units ensure your process or tools have oil-free air. Our low rpm pumps provide reliable air for any applications and are manufactured for durability and long life. Built with the most heavy-duty components found in piston compressors today.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
More Info
- All UL electrical controls
- ASME/CRN powder coated air receiver
- Auto start/stop
- Magnetic motor starter
- Fully enclosed belt guard
- Heavy-duty air filters
- Heavy-duty industrial-grade electric motor
- Heavy-duty single-stage oil-free industrial-grade pump
Generator / Welder Features
- All basic features
- Belt guard aftercooler
- Tank discharge ball valve
- Vibration pads
5 HP OIL-FREE INDUSTRIAL DUTY COMPRESSOR
17 cfm @ 125 psi
No Start-Up Kit Required
Oil-free compressors are designed for the medical, agricultural, food, beverage and laboratory environments. These units ensure your process or tools have oil-free air. Our low rpm pumps provide reliable air for any applications and are manufactured for durability and long life. Built with the most heavy-duty components found in piston compressors today.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
More Info
- All UL electrical controls
- ASME/CRN powder coated air receiver
- Auto start/stop
- Magnetic motor starter
- Fully enclosed belt guard
- Heavy-duty air filters
- Heavy-duty industrial-grade electric motor
- Heavy-duty single-stage oil-free industrial-grade pump
Generator / Welder Features
- All basic features
- Belt guard aftercooler
- Tank discharge ball valve
- Vibration pads
7.5 HP OIL-FREE INDUSTRIAL DUTY COMPRESSOR
21 cfm @ 125 psi
No Start-Up Kit Required
Oil-free compressors are designed for the medical, agricultural, food, beverage and laboratory environments. These units ensure your process or tools have oil-free air. Our low rpm pumps provide reliable air for any applications and are manufactured for durability and long life. Built with the most heavy-duty components found in piston compressors today.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
More Info
- All UL electrical controls
- ASME/CRN powder coated air receiver
- Auto start/stop
- Magnetic motor starter
- Fully enclosed belt guard
- Heavy-duty air filters
- Heavy-duty industrial-grade electric motor
- Heavy-duty single-stage oil-free industrial-grade pump
Generator / Welder Features
- All basic features
- Belt guard aftercooler
- Tank discharge ball valve
- Vibration pads
10 HP OIL-FREE INDUSTRIAL DUTY COMPRESSOR
34 cfm @ 125 psi
No Start-Up Kit Required
Oil-free compressors are designed for the medical, agricultural, food, beverage and laboratory environments. These units ensure your process or tools have oil-free air. Our low rpm pumps provide reliable air for any applications and are manufactured for durability and long life. Built with the most heavy-duty components found in piston compressors today.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
More Info
- All UL electrical controls
- ASME/CRN powder coated air receiver
- Auto start/stop
- Magnetic motor starter
- Fully enclosed belt guard
- Heavy-duty air filters
- Heavy-duty industrial-grade electric motor
- Heavy-duty single-stage oil-free industrial-grade pump
Generator / Welder Features
- All basic features
- Belt guard aftercooler
- Tank discharge ball valve
- Vibration pads
15 HP OIL-FREE INDUSTRIAL DUTY COMPRESSOR
45 cfm @ 125 psi
No Start-Up Kit Required
Oil-free compressors are designed for the medical, agricultural, food, beverage and laboratory environments. These units ensure your process or tools have oil-free air. Our low rpm pumps provide reliable air for any applications and are manufactured for durability and long life. Built with the most heavy-duty components found in piston compressors today.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
More Info
- All UL electrical controls
- ASME/CRN powder coated air receiver
- Auto start/stop
- Magnetic motor starter
- Fully enclosed belt guard
- Heavy-duty air filters
- Heavy-duty industrial-grade electric motor
- Heavy-duty single-stage oil-free industrial-grade pump
Generator / Welder Features
- All basic features
- Belt guard aftercooler
- Tank discharge ball valve
- Vibration pads
20 HP OIL-FREE INDUSTRIAL DUTY COMPRESSOR
64 cfm @ 125 psi
No Start-Up Kit Required
Oil-free compressors are designed for the medical, agricultural, food, beverage and laboratory environments. These units ensure your process or tools have oil-free air. Our low rpm pumps provide reliable air for any applications and are manufactured for durability and long life. Built with the most heavy-duty components found in piston compressors today.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
More Info
- All UL electrical controls
- ASME/CRN powder coated air receiver
- Auto start/stop
- Magnetic motor starter
- Fully enclosed belt guard
- Heavy-duty air filters
- Heavy-duty industrial-grade electric motor
- Heavy-duty single-stage oil-free industrial-grade pump
Generator / Welder Features
- All basic features
- Belt guard aftercooler
- Tank discharge ball valve
- Vibration pads
25 HP OIL-FREE INDUSTRIAL DUTY COMPRESSOR
76 cfm @ 125 psi
No Start-Up Kit Required
Oil-free compressors are designed for the medical, agricultural, food, beverage and laboratory environments. These units ensure your process or tools have oil-free air. Our low rpm pumps provide reliable air for any applications and are manufactured for durability and long life. Built with the most heavy-duty components found in piston compressors today.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
More Info
- All UL electrical controls
- ASME/CRN powder coated air receiver
- Auto start/stop
- Magnetic motor starter
- Fully enclosed belt guard
- Heavy-duty air filters
- Heavy-duty industrial-grade electric motor
- Heavy-duty single-stage oil-free industrial-grade pump
Generator / Welder Features
- All basic features
- Belt guard aftercooler
- Tank discharge ball valve
- Vibration pads
30 HP OIL-FREE INDUSTRIAL DUTY COMPRESSOR
97 cfm @ 125 psi
No Start-Up Kit Required
Oil-free compressors are designed for the medical, agricultural, food, beverage and laboratory environments. These units ensure your process or tools have oil-free air. Our low rpm pumps provide reliable air for any applications and are manufactured for durability and long life. Built with the most heavy-duty components found in piston compressors today.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
More Info
- All UL electrical controls
- ASME/CRN powder coated air receiver
- Auto start/stop
- Magnetic motor starter
- Fully enclosed belt guard
- Heavy-duty air filters
- Heavy-duty industrial-grade electric motor
- Heavy-duty single-stage oil-free industrial-grade pump
Generator / Welder Features
- All basic features
- Belt guard aftercooler
- Tank discharge ball valve
- Vibration pads
2 HP OIL-FREE DUPLEX COMPRESSORS
12 cfm @ 125 psi
No Start-Up Kit Required
Designed for the medical, agricultural, food, beverage and laboratory environments to ensure your process or tools have oil-free air, duplex oil-free compressors are the ultimate in electrical efficiency. Built in redundancy and the capacity to deliver twice the power in the same amount of space as a typical compressors, our duplex oil-free compressors provide additional air when needed, are easy to service, maintain and operate. All units feature heavy-duty cast iron low-RPM pumps manufactured for durability and long life and heavy-duty components.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
More Info
- All UL electrical controls
- ASME/CRN powder coated air receiver
- Auto start/stop
- Magnetic motor starter
- Fully enclosed belt guard
- Heavy-duty air filters
- Heavy-duty industrial-grade electric motor
- Heavy-duty single-stage oil-free industrial-grade pump
Generator / Welder Features
- All basic features
- Belt guard aftercooler
- Tank discharge ball valve
- Vibration pads
3 HP OIL-FREE DUPLEX COMPRESSORS
20 cfm @ 125 psi
No Start-Up Kit Required
Designed for the medical, agricultural, food, beverage and laboratory environments to ensure your process or tools have oil-free air, duplex oil-free compressors are the ultimate in electrical efficiency. Built in redundancy and the capacity to deliver twice the power in the same amount of space as a typical compressors, our duplex oil-free compressors provide additional air when needed, are easy to service, maintain and operate. All units feature heavy-duty cast iron low-RPM pumps manufactured for durability and long life and heavy-duty components.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
More Info
- All UL electrical controls
- ASME/CRN powder coated air receiver
- Auto start/stop
- Magnetic motor starter
- Fully enclosed belt guard
- Heavy-duty air filters
- Heavy-duty industrial-grade electric motor
- Heavy-duty single-stage oil-free industrial-grade pump
Generator / Welder Features
- All basic features
- Belt guard aftercooler
- Tank discharge ball valve
- Vibration pads
5 HP OIL-FREE DUPLEX INDUSTRIAL DUTY COMPRESSORS
34 cfm @ 125 psi
No Start-Up Kit Required
Designed for the medical, agricultural, food, beverage and laboratory environments to ensure your process or tools have oil-free air, duplex oil-free compressors are the ultimate in electrical efficiency. Built in redundancy and the capacity to deliver twice the power in the same amount of space as a typical compressors, our duplex oil-free compressors provide additional air when needed, are easy to service, maintain and operate. All units feature heavy-duty cast iron low-RPM pumps manufactured for durability and long life and heavy-duty components.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
More Info
- All UL electrical controls
- ASME/CRN powder coated air receiver
- Auto start/stop
- Magnetic motor starter
- Fully enclosed belt guard
- Heavy-duty air filters
- Heavy-duty industrial-grade electric motor
- Heavy-duty single-stage oil-free industrial-grade pump
Generator / Welder Features
- All basic features
- Belt guard aftercooler
- Tank discharge ball valve
- Vibration pads
7.5 HP OIL-FREE DUPLEX COMPRESSORS
42 cfm @ 125 psi
No Start-Up Kit Required
Designed for the medical, agricultural, food, beverage and laboratory environments to ensure your process or tools have oil-free air, duplex oil-free compressors are the ultimate in electrical efficiency. Built in redundancy and the capacity to deliver twice the power in the same amount of space as a typical compressors, our duplex oil-free compressors provide additional air when needed, are easy to service, maintain and operate. All units feature heavy-duty cast iron low-RPM pumps manufactured for durability and long life and heavy-duty components.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
More Info
- All UL electrical controls
- ASME/CRN powder coated air receiver
- Auto start/stop
- Magnetic motor starter
- Fully enclosed belt guard
- Heavy-duty air filters
- Heavy-duty industrial-grade electric motor
- Heavy-duty single-stage oil-free industrial-grade pump
Generator / Welder Features
- All basic features
- Belt guard aftercooler
- Tank discharge ball valve
- Vibration pads
10 HP OIL-FREE INDUSTRIAL DUTY COMPRESSOR
Time Delay 68 cfm @ 125 psi
Alternating 34 cfm @ 125 psi
No Start-Up Kit Required
Designed for the medical, agricultural, food, beverage and laboratory environments to ensure your process or tools have oil-free air, duplex oil-free compressors are the ultimate in electrical efficiency. Built in redundancy and the capacity to deliver twice the power in the same amount of space as a typical compressors, our duplex oil-free compressors provide additional air when needed, are easy to service, maintain and operate. All units feature heavy-duty cast iron low-RPM pumps manufactured for durability and long life and heavy-duty components.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
More Info
- All UL electrical controls
- ASME/CRN powder coated air receiver
- Auto start/stop
- Magnetic motor starter
- Fully enclosed belt guard
- Heavy-duty air filters
- Heavy-duty industrial-grade electric motor
- Heavy-duty single-stage oil-free industrial-grade pump
Generator / Welder Features
- All basic features
- Belt guard aftercooler
- Tank discharge ball valve
- Vibration pads
15 HP OIL-FREE DUPLEX COMPRESSORS
Time Delay 90 cfm @ 125 psi
Alternating 45 cfm @ 125 psi
No Start-Up Kit Required
Designed for the medical, agricultural, food, beverage and laboratory environments to ensure your process or tools have oil-free air, duplex oil-free compressors are the ultimate in electrical efficiency. Built in redundancy and the capacity to deliver twice the power in the same amount of space as a typical compressors, our duplex oil-free compressors provide additional air when needed, are easy to service, maintain and operate. All units feature heavy-duty cast iron low-RPM pumps manufactured for durability and long life and heavy-duty components.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
More Info
- All UL electrical controls
- ASME/CRN powder coated air receiver
- Auto start/stop
- Magnetic motor starter
- Fully enclosed belt guard
- Heavy-duty air filters
- Heavy-duty industrial-grade electric motor
- Heavy-duty single-stage oil-free industrial-grade pump
Generator / Welder Features
- All basic features
- Belt guard aftercooler
- Tank discharge ball valve
- Vibration pads
20 HP OIL-FREE DUPLEX COMPRESSORS
Time Delay 128 cfm @ 125 psi
Alternating 64 cfm @ 125 psi
No Start-Up Kit Required
Designed for the medical, agricultural, food, beverage and laboratory environments to ensure your process or tools have oil-free air, duplex oil-free compressors are the ultimate in electrical efficiency. Built in redundancy and the capacity to deliver twice the power in the same amount of space as a typical compressors, our duplex oil-free compressors provide additional air when needed, are easy to service, maintain and operate. All units feature heavy-duty cast iron low-RPM pumps manufactured for durability and long life and heavy-duty components.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
More Info
- All UL electrical controls
- ASME/CRN powder coated air receiver
- Auto start/stop
- Magnetic motor starter
- Fully enclosed belt guard
- Heavy-duty air filters
- Heavy-duty industrial-grade electric motor
- Heavy-duty single-stage oil-free industrial-grade pump
Generator / Welder Features
- All basic features
- Belt guard aftercooler
- Tank discharge ball valve
- Vibration pads
25 HP OIL-FREE DUPLEX COMPRESSORS
Time Delay 152 cfm @ 125 psi
Alternating 76 cfm @ 125 psi
No Start-Up Kit Required
Designed for the medical, agricultural, food, beverage and laboratory environments to ensure your process or tools have oil-free air, duplex oil-free compressors are the ultimate in electrical efficiency. Built in redundancy and the capacity to deliver twice the power in the same amount of space as a typical compressors, our duplex oil-free compressors provide additional air when needed, are easy to service, maintain and operate. All units feature heavy-duty cast iron low-RPM pumps manufactured for durability and long life and heavy-duty components.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
More Info
- All UL electrical controls
- ASME/CRN powder coated air receiver
- Auto start/stop
- Magnetic motor starter
- Fully enclosed belt guard
- Heavy-duty air filters
- Heavy-duty industrial-grade electric motor
- Heavy-duty single-stage oil-free industrial-grade pump
Generator / Welder Features
- All basic features
- Belt guard aftercooler
- Tank discharge ball valve
- Vibration pads
30 HP OIL-FREE DUPLEX COMPRESSORS
Time Delay 194 cfm @ 125 psi
Alternating 97 cfm @ 125 psi
No Start-Up Kit Required
Designed for the medical, agricultural, food, beverage and laboratory environments to ensure your process or tools have oil-free air, duplex oil-free compressors are the ultimate in electrical efficiency. Built in redundancy and the capacity to deliver twice the power in the same amount of space as a typical compressors, our duplex oil-free compressors provide additional air when needed, are easy to service, maintain and operate. All units feature heavy-duty cast iron low-RPM pumps manufactured for durability and long life and heavy-duty components.
Elite Series compressors feature a unique option package that makes our compressors simpler to maintain while delivering higher quality air.
More Info
- All UL electrical controls
- ASME/CRN powder coated air receiver
- Auto start/stop
- Magnetic motor starter
- Fully enclosed belt guard
- Heavy-duty air filters
- Heavy-duty industrial-grade electric motor
- Heavy-duty single-stage oil-free industrial-grade pump
Generator / Welder Features
- All basic features
- Belt guard aftercooler
- Tank discharge ball valve
- Vibration pads